Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.

Suzuki 800 Intruder Club & Forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder
 
HomePublicationsRegisterLog in

Share | 
 

 M50 Lowers

Go down 
AuthorMessage
alfie92
Very Valued VIP Member
avatar


PostSubject: M50 Lowers   Tue Apr 03, 2012 5:20 pm

What I found with this mod is that you must make a template first,the things to look out for are
1: any interference when forks fully depressed. 2: If you have a crash bar fitted check for clearance on full lock.The sizes are good for my fitment but make a template first save yourself time,the material I used was 6mm clear plastic,20mm x 20mm ali angle and 50mm/70mm jubilee clips.I got the angle from B&Q £5. 6mm clear plastic surplus material railway,(old advert cover)jubilee clips 10 for £2.61 Toolstation.Cheap mod thanks to Grob (ippikin)



Back to top Go down
Mr Intruder
Suzuki800.com Founder ... & ... Senior Administrator
avatar


PostSubject: Re: M50 Lowers   Tue Apr 03, 2012 7:04 pm

Excellent job done Alfie
I went to make some for mine the other day but couldn't as I have next to no clearance between my forks and crash bars
Back to top Go down
captain crash
Mentally Deficient lunatic ..... & ..... Site Moderator
avatar


PostSubject: Re: M50 Lowers   Tue Apr 03, 2012 8:03 pm

Another fine job done Alfie, You need to update your signiture, I reckon you will be giving Mr I a run for his money now
Back to top Go down
alfie92
Very Valued VIP Member
avatar


PostSubject: Re: M50 Lowers   Wed Apr 04, 2012 8:45 pm

Dave make cutouts were your crash bar hits.
Back to top Go down
captain crash
Mentally Deficient lunatic ..... & ..... Site Moderator
avatar


PostSubject: Re: M50 Lowers   Thu Apr 05, 2012 12:56 am

Now that's thinking outside the box
Back to top Go down
alfie92
Very Valued VIP Member
avatar


PostSubject: Re: M50 Lowers   Thu Apr 05, 2012 5:16 pm

Bearing in mind Dave that the forks go up and down unlike your crash bar.
Back to top Go down
Mr Intruder
Suzuki800.com Founder ... & ... Senior Administrator
avatar


PostSubject: Re: M50 Lowers   Fri Apr 06, 2012 5:22 am

Good advice Alfie, I will look at this again with your thinking in mind.
Back to top Go down
Sponsored content




PostSubject: Re: M50 Lowers   

Back to top Go down
 
M50 Lowers
Back to top 
Page 1 of 1

Permissions in this forum:You cannot reply to topics in this forum
Suzuki 800 Intruder Club & Forum :: The Garage :: Screens, Lowers & Wind deflectors.-
Jump to:  
Slide Show
A random selection of suzuki800.com member bikes.
Latest topics
» Hello from USA Eastern coast
by ardie Today at 9:25 pm

» northworks custom motorcycles from Portugal
by ardie Today at 9:24 pm

» cam chain timing marks on stator ?
by cidere Today at 3:59 pm

» Custom Suzuki Intruder 800 by Northworks motorcycles
by peardrop3 Today at 3:11 pm

» Saddlemen Profiler on Suzuki Intruder C800 / VL800
by Richard Today at 10:27 am

» The mystery of the Intruder 800 Highway bars
by MikeKKim Yesterday at 7:14 pm

» My Baby has arrived
by fat intruder Yesterday at 6:38 pm

» Eatting through sparks
by trevski Yesterday at 1:07 am

» hellow from kerry
by fat intruder Fri Aug 10, 2018 5:06 pm

» Hello
by fat intruder Fri Aug 10, 2018 4:56 pm

» Hello from a newbe
by fat intruder Fri Aug 10, 2018 4:38 pm

» hello from pembrokeshire
by fat intruder Fri Aug 10, 2018 4:32 pm

» When the bastards grind you down I find this helps.
by fat intruder Fri Aug 10, 2018 4:31 pm

» Hi from Finland!
by fat intruder Fri Aug 10, 2018 4:10 pm

» Hello
by fat intruder Fri Aug 10, 2018 3:54 pm

» Just built me a bobber from a VL800
by OldManYam Wed Aug 08, 2018 9:17 pm

» Home-Made Rotor Resurfacing (Read "Red-Neck Refurb!")
by bagtoracer68 Tue Aug 07, 2018 10:00 pm

» VX 800 Oil level
by BudPotter Tue Aug 07, 2018 5:48 am

» Needle Placement
by badtazboy Mon Aug 06, 2018 6:33 pm

» Help me please - starting issue.
by Hegel8 Fri Aug 03, 2018 8:44 pm

Log in
Username:
Password:
Log in automatically: 
:: I forgot my password