Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.

Suzuki 800 Intruder Club & Forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder
 
HomePublicationsRegisterLog in

Share | 
 

 Took baffles out (highway hawk pipes)

Go down 
AuthorMessage
Goshawkmark123
Member



PostSubject: Took baffles out (highway hawk pipes)    Tue Jun 12, 2018 9:19 pm

Ok guys took baffles outa pipes two minit job couple grubscrews an out they poped.... Now tberes not awful lot louder a bit dissapointing realy so took blast down motorway all good no change then pulling away from lights loud pop and boom shes realy rumbling and throaty much as i expected by removing baffles.... Looking and listening though the rear pot (top pipe)  is definatly louder and bottom pipe a bit muted still.... So my question is, is there a secondry baffle of sorts further along?  And i have blown one out?  Any ideas...... By way sounds great now and throttle responce lot quicker. Although no popping on overrun
Back to top Go down
captain morgan
Member



PostSubject: Re: Took baffles out (highway hawk pipes)    Thu Jun 14, 2018 7:36 pm

I don't no for sure but they are after market pipes so I cant imaging there are secondary baffles but there could be????
Back to top Go down
hawktheslayer
Very Valued VIP Member
avatar


PostSubject: Re: Took baffles out (highway hawk pipes)    Sat Jun 16, 2018 8:55 pm

NO 2nd baffle. db on the low scale so like a sub woofer your ears will  not actually register where the noise comes from! if it runs well sounds good then don't try to fix it!
Back to top Go down
Goshawkmark123
Member



PostSubject: Re: Took baffles out (highway hawk pipes)    Tue Jun 19, 2018 3:32 pm

Well had torch down pipe and low behold a second baffle wrapped in fibre bit twisting with 18"coldchisel an out it popped can only presume that's what shot out top pipe other day now sounds sweet an balanced an goes like fek lol
Back to top Go down
captain morgan
Member



PostSubject: Re: Took baffles out (highway hawk pipes)    Tue Jun 26, 2018 6:37 pm

lol job done 
Back to top Go down
Sponsored content




PostSubject: Re: Took baffles out (highway hawk pipes)    

Back to top Go down
 
Took baffles out (highway hawk pipes)
Back to top 
Page 1 of 1

Permissions in this forum:You cannot reply to topics in this forum
Suzuki 800 Intruder Club & Forum :: The Garage :: Exhaust-
Jump to:  
Slide Show
A random selection of suzuki800.com member bikes.
Latest topics
» new to this board - VX 800 in Europ-version
by malaga Yesterday at 9:20 pm

» cam chain timing marks on stator ?
by cidere Yesterday at 10:36 am

» My Baby has arrived
by fat intruder Fri Aug 17, 2018 4:25 pm

» Hello from USA Eastern coast
by ardie Thu Aug 16, 2018 9:25 pm

» northworks custom motorcycles from Portugal
by ardie Thu Aug 16, 2018 9:24 pm

» Custom Suzuki Intruder 800 by Northworks motorcycles
by peardrop3 Thu Aug 16, 2018 3:11 pm

» Saddlemen Profiler on Suzuki Intruder C800 / VL800
by Richard Thu Aug 16, 2018 10:27 am

» The mystery of the Intruder 800 Highway bars
by MikeKKim Wed Aug 15, 2018 7:14 pm

» Eatting through sparks
by trevski Wed Aug 15, 2018 1:07 am

» hellow from kerry
by fat intruder Fri Aug 10, 2018 5:06 pm

» Hello
by fat intruder Fri Aug 10, 2018 4:56 pm

» Hello from a newbe
by fat intruder Fri Aug 10, 2018 4:38 pm

» hello from pembrokeshire
by fat intruder Fri Aug 10, 2018 4:32 pm

» When the bastards grind you down I find this helps.
by fat intruder Fri Aug 10, 2018 4:31 pm

» Hi from Finland!
by fat intruder Fri Aug 10, 2018 4:10 pm

» Hello
by fat intruder Fri Aug 10, 2018 3:54 pm

» Just built me a bobber from a VL800
by OldManYam Wed Aug 08, 2018 9:17 pm

» Home-Made Rotor Resurfacing (Read "Red-Neck Refurb!")
by bagtoracer68 Tue Aug 07, 2018 10:00 pm

» VX 800 Oil level
by BudPotter Tue Aug 07, 2018 5:48 am

» Needle Placement
by badtazboy Mon Aug 06, 2018 6:33 pm

Log in
Username:
Password:
Log in automatically: 
:: I forgot my password