Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.

Suzuki 800 Intruder Club & Forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder
 
HomePublicationsRegisterLog in

Share
 

 F1 Code after Gman controller

Go down 
AuthorMessage
Richard
Prospect
Richard


F1 Code after Gman controller Empty
PostSubject: F1 Code after Gman controller   F1 Code after Gman controller Icon_minitimeMon Jul 08, 2019 10:25 pm

Fitted new vance and hines pipes, K&N plus Gman controller.  Im getting an F1 error message.  I plugged the o2 sensor and fitted an eliminator to the oxygen sensor port, but still F1 code.

Any ideas, Gman are sending me an alternative eliminator as i noticed there are 4 wires and the eliminator only picks up 2 out of the 4, the guys i purchased the eliminator from suggest you only need to block off the two cables.

Bike rides great, responsive and really nice acceleration, just nervous im doing damage by riding, ligh only comes on after riding for about 5 mins, im pretty certain its because of the oxygen sensor, any way to check?

Any advice much appreciated?
Back to top Go down
Richard
Prospect
Richard


F1 Code after Gman controller Empty
PostSubject: Re: F1 Code after Gman controller   F1 Code after Gman controller Icon_minitimeFri Aug 09, 2019 5:17 pm

Ill answer my own question as i found the solution.  

To stop the F1 you need to cut the appropriate cable in the ECU, while daunting seems to have done the trick and all working ok.

Gmann controller seems to make a huge difference to responsiveness of the throttle and general control and acceleration
Back to top Go down
 
F1 Code after Gman controller
Back to top 
Page 1 of 1
 Similar topics
-
» The 411 on the MSD Charge FI Controller for the Kawasaki Teryx
» Glossary of RAF mission code names
» Pre-Season Ticket Code
» CombatSportSupply.com Coupon Code
» RMATV Code

Permissions in this forum:You cannot reply to topics in this forum
Suzuki 800 Intruder Club & Forum :: The Garage :: FueI Injection Modules, Fuel, Jetting & Modifications, etc-
Jump to:  
Slide Show
A random selection of suzuki800.com member bikes.
Latest topics
» Introduction
F1 Code after Gman controller Icon_minitimeby stingray Today at 2:57 pm

» Tailbone pain after 100 miles on stock seat.
F1 Code after Gman controller Icon_minitimeby bob gibson Wed Nov 06, 2019 6:39 pm

» Electronic fuel injection
F1 Code after Gman controller Icon_minitimeby 03580 Wed Nov 06, 2019 2:18 pm

» Straight Shots on 2006 C800
F1 Code after Gman controller Icon_minitimeby Tucker Tue Nov 05, 2019 7:57 pm

» Just a little help.
F1 Code after Gman controller Icon_minitimeby silvergriffin21 Mon Nov 04, 2019 6:45 pm

» hi guys
F1 Code after Gman controller Icon_minitimeby ardie Mon Nov 04, 2019 12:07 pm

» Hello from a newbie in the U.K.
F1 Code after Gman controller Icon_minitimeby GPDave Mon Nov 04, 2019 9:00 am

» Insurance
F1 Code after Gman controller Icon_minitimeby ardie Sat Nov 02, 2019 12:50 pm

» Chase Williams in Tennessee
F1 Code after Gman controller Icon_minitimeby stingray Fri Nov 01, 2019 10:10 pm

» Hello From Hollister MO, USA!
F1 Code after Gman controller Icon_minitimeby Proudtexson Fri Oct 25, 2019 12:29 am

» Hello, ne member from uk
F1 Code after Gman controller Icon_minitimeby ardie Tue Oct 22, 2019 6:44 pm

» Hello, new member from uk
F1 Code after Gman controller Icon_minitimeby stingray Mon Oct 21, 2019 2:42 pm

» VL800 / VZ800 Carb Jetting Guide
F1 Code after Gman controller Icon_minitimeby muppet Sun Oct 20, 2019 8:24 pm

» hi from Onterrible Canada! Formerly from bC Canada !
F1 Code after Gman controller Icon_minitimeby BirdMan Sun Oct 20, 2019 2:09 am

» 1999 vz800 rear light change
F1 Code after Gman controller Icon_minitimeby BirdMan Sun Oct 20, 2019 2:07 am

» VL and VZ exhausts interchangeable?
F1 Code after Gman controller Icon_minitimeby Asmotsat Wed Oct 16, 2019 1:26 pm

» hello from Antalya/TURKEY
F1 Code after Gman controller Icon_minitimeby stingray Thu Oct 10, 2019 11:27 am

» New Guy
F1 Code after Gman controller Icon_minitimeby stingray Thu Oct 10, 2019 11:24 am

» Hello from California!
F1 Code after Gman controller Icon_minitimeby ArnoldinIdaho Mon Oct 07, 2019 12:21 am

» Springer front end - please help
F1 Code after Gman controller Icon_minitimeby Hegel8 Sat Oct 05, 2019 3:53 am

Log in
Username:
Password:
Log in automatically: 
:: I forgot my password