
Suzuki 800 Intruder Club & Forum A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder |
| | 16mm metal rod down the exhaust | |
|
+2captain crash fat intruder 6 posters | Author | Message |
---|
fat intruder Very Valued VIP Member

 | Subject: 16mm metal rod down the exhaust Wed Oct 15, 2014 7:50 pm | |
| did the first mod to my bike today after I got it home (VZ800, 2009) stock exhaust was very quite so I got out my trusty 8mm length of thread with a sharpened end and knocked it down the exhaust with a club hammer went through what felt like two plates took it out started up the bike sounded a little better but still very quite and lacked any sort of deeper sound so I went strait on to a 16mm (I think? it's big!!) metal rod got out my little angle grinder and sharpened up the end then knocked that through with my friendly persuader (club hammer) did the job bike now has a deeper sound still pretty quite so should keep everyone happy in fact the bike I just got rid of was much louder  have yet to take it out since doing it coz it started to pee down with rain so will get out tomorrow and see what it sounds like going along | |
|  | | captain crash Mentally Deficient lunatic ..... & ..... Site Moderator

 | Subject: Re: 16mm metal rod down the exhaust Wed Oct 15, 2014 7:58 pm | |
| Rod & persuader, every tool box should have them  | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Wed Oct 15, 2014 8:08 pm | |
| ohhhhh yes  | |
|  | | simbo * Site Guru *

 | Subject: Re: 16mm metal rod down the exhaust Wed Oct 15, 2014 9:18 pm | |
| I bet it sounds a whole lot better  | |
|  | | DocSjulle Hero Globs

 | Subject: Re: 16mm metal rod down the exhaust Wed Oct 15, 2014 9:26 pm | |
| Congratulations with the new bike Drill four 10-12mm holes in each end baffle, and you'll get a much nicer sound without it being too loud. My friend is very happy with his bike after this mod. | |
|  | | Mr Intruder Suzuki800.com Founder ... & ... Senior Administrator

 | Subject: Re: 16mm metal rod down the exhaust Wed Oct 15, 2014 9:36 pm | |
| Good on you Morgan, bet that sounds better. yes you were right it was 2 plates you went through. | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Wed Oct 15, 2014 11:03 pm | |
| what's the third thing I hit after the two plates then? lol, yep it sounds better will check it out tomorrow. was maybe thinking of that Kim but then you can tell it's been tampered with I like it looking stock that way if you sell the bike at a later date they will look like stock pipes that nobody has messed with I may possibly knock an even bigger metal rod through not that I will be able to go a lot bigger lol once I have the money I will get after market pipes for the bike but for now it should do the job | |
|  | | stingray Very Valued VIP Member

 | |  | | DocSjulle Hero Globs

 | Subject: Re: 16mm metal rod down the exhaust Thu Oct 16, 2014 12:11 am | |
| - fat intruder wrote:
- what's the third thing I hit after the two plates then?
It's the catalytic converter. If you use a flashlight you should be able to see the honeycomb structure. | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Thu Oct 16, 2014 12:41 am | |
| ok thanks Kim take it I don't want to punch through in to that | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Thu Oct 16, 2014 3:55 pm | |
| took my bike out still very quite so I thought bollox to it and put four10mm holes in each back box am going for a ride in a mo soooo will see if it sounds better. cant find my 12mm drill bit bugger | |
|  | | DocSjulle Hero Globs

 | Subject: Re: 16mm metal rod down the exhaust Thu Oct 16, 2014 6:52 pm | |
| | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Thu Oct 16, 2014 11:46 pm | |
| to be honest it's still not that loud but does sound a lot better will do for now first mod to the bike finished | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Mon Oct 20, 2014 1:37 pm | |
| after riding my bike a bit more yes I did like it sounded a lot better than stock but still needed a bit of adjustment so I got hold of another bit of metal rod which was bigger deffo 20mm (maybe 22mm) this one is big ,sharpened up the end and knocked it down each pipe sound is deeper will give it a ride later and test it out | |
|  | | fat intruder Very Valued VIP Member

 | Subject: Re: 16mm metal rod down the exhaust Tue Oct 21, 2014 6:01 pm | |
| tested the bike last night and today, it now sounds more like a cruiser still would not upset anyone but has a much nicer sound than stock would recommend 20mm down the pipes and four 10mm holes in the end to anyone who would like a little more sound and a deeper tone to there stock exhaust  | |
|  | | Sponsored content
 | Subject: Re: 16mm metal rod down the exhaust  | |
| |
|  | | | 16mm metal rod down the exhaust | |
|
Similar topics |  |
|
| Permissions in this forum: | You cannot reply to topics in this forum
| |
| |
| |
Slide Show | A random selection of suzuki800.com member bikes. |
Latest topics | » Greetings
by tkennar Mon Mar 20, 2023 4:47 pm
» Greetings and salutations
by JimboJ Sun Mar 12, 2023 1:14 pm
» two into one exhaust
by beachartist Sun Mar 12, 2023 12:50 am
» New member
by Kev Sat Mar 11, 2023 9:02 am
» Another Sachs Roadster
by adilmon Fri Mar 10, 2023 2:08 pm
» New member
by Born to be mild Thu Mar 02, 2023 11:10 am
» Headlight fix
by flying1 Wed Mar 01, 2023 9:43 am
» REV Counter stops when lights are on???
by Damion Jones Sun Feb 26, 2023 8:00 pm
» Headlamp
by flying1 Sat Feb 25, 2023 10:08 pm
» Hi everyone newbie thanks for letting me join
by flying1 Sat Feb 25, 2023 4:52 pm
» VX800 - Wiring issue colours & diagram?
by Damion Jones Fri Feb 24, 2023 11:59 pm
» Vz800 crankshaft
by Big Rab Thu Feb 23, 2023 6:18 pm
» Final drive
by ardie Tue Feb 14, 2023 7:14 pm
» My 2002 VS800
by Badger Sun Feb 12, 2023 4:31 pm
» Engine timing
by Big Rab Mon Feb 06, 2023 5:25 pm
» New member
by Bobby Thu Feb 02, 2023 2:41 pm
» New member
by Ray Noble Wed Jan 18, 2023 11:19 am
» ciao
by gioniko73 Tue Jan 17, 2023 12:09 am
» Introduction
by james mclaughlin Sat Jan 14, 2023 4:01 pm
» vs750/800 handle bar switches wiring
by Badger Thu Jan 12, 2023 3:17 pm
|
|