Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.
Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.
Suzuki 800 Intruder Club & Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Suzuki 800 Intruder Club & Forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder
 
HomeRegisterLog in

 

 Bar end removal help please!

Go down 
2 posters
AuthorMessage
Bluesman
Very Valued VIP Member
Bluesman


Bar end removal help please! Empty
PostSubject: Bar end removal help please!   Bar end removal help please! Icon_minitimeFri Jan 22, 2016 10:02 pm

I've usually no problem removing and refitting bar ends but for some reason I just can't get these buggers out! I loosened the screw about 3 turns not to lose things inside. The rubber expander starts to move about 1/4" but no matter how much I wiggle I can't seem to get either side out! I've unscrewed a couple more turns and dare not risk more. Where am I going wrong? WD 40 maybe?
Back to top Go down
simbo
* Site Guru *
simbo


Bar end removal help please! Empty
PostSubject: Re: Bar end removal help please!   Bar end removal help please! Icon_minitimeSat Jan 23, 2016 2:31 pm

Have you unscrewed the screw a bit and then tapped it in to release the expanding grommet? WD-40 might work if the rubbers stuck inside? I have a stock bar end weight with fitting attached if you need a picture to see the make up of them?.
Back to top Go down
Bluesman
Very Valued VIP Member
Bluesman


Bar end removal help please! Empty
PostSubject: Re: Bar end removal help please!   Bar end removal help please! Icon_minitimeSat Jan 23, 2016 3:31 pm

simbo wrote:
Have you unscrewed the screw a bit and then tapped it in to release the expanding grommet? WD-40 might work if the rubbers stuck inside? I have a stock bar end weight with fitting attached if you need a picture to see the make up of them?.
Success. With a couple of bashes to push the screw, a couple of squirts of WD40 and a lot of wiggling out the throttle side came! Thanks Sim!
Back to top Go down
Sponsored content




Bar end removal help please! Empty
PostSubject: Re: Bar end removal help please!   Bar end removal help please! Icon_minitime

Back to top Go down
 
Bar end removal help please!
Back to top 
Page 1 of 1
 Similar topics
-
» Shifter knob removal
» Rhino rear sway bar removal
» King Quad 450 Diff Lock Limiter Removal
» axle shaft removal
» murray widebody steering wheel removal.

Permissions in this forum:You cannot reply to topics in this forum
Suzuki 800 Intruder Club & Forum :: The Garage :: Risers, Handle bars, Mirrors, Grips & End Weights-
Jump to:  
Slide Show
A random selection of suzuki800.com member bikes.
Latest topics
» Top Yoke Covers
Bar end removal help please! Icon_minitimeby Badger Yesterday at 12:04 pm

» vs 1400 final drive in a vs 800
Bar end removal help please! Icon_minitimeby admin Tue Sep 21, 2021 7:36 pm

» New to bike world
Bar end removal help please! Icon_minitimeby Truckerjer Tue Sep 21, 2021 1:36 pm

» Cable extentions or rerouting for raised bars?
Bar end removal help please! Icon_minitimeby hmac Sat Sep 18, 2021 2:41 pm

» Adding a electronic
Bar end removal help please! Icon_minitimeby Truckerjer Fri Sep 17, 2021 10:41 pm

» Hola from Spain!
Bar end removal help please! Icon_minitimeby Badger Tue Sep 14, 2021 3:58 pm

» Hello from the USA
Bar end removal help please! Icon_minitimeby wildcatvs800 Mon Sep 13, 2021 9:02 pm

» VX800 Forks failing after just a few days of simple use?
Bar end removal help please! Icon_minitimeby Damion Jones Sun Sep 12, 2021 10:25 pm

» Hi there. 2012 Intruder M50
Bar end removal help please! Icon_minitimeby jp.hindle@btinternet.com Thu Sep 09, 2021 6:37 pm

» 2008 Suzuki C800T genuine saddlebags
Bar end removal help please! Icon_minitimeby Johnmc800 Thu Sep 09, 2021 5:53 pm

» List of mods - Bike is finally complete - Marauder VZ800
Bar end removal help please! Icon_minitimeby botskabouter Fri Sep 03, 2021 11:40 am

» hello all,
Bar end removal help please! Icon_minitimeby Petrolhead750 Thu Sep 02, 2021 7:51 pm

» Oil leak from 1994 VS800 Intruder - right side, but only while running
Bar end removal help please! Icon_minitimeby MikeKKim Wed Sep 01, 2021 12:23 am

» New member saying hello
Bar end removal help please! Icon_minitimeby Johnmc800 Tue Aug 31, 2021 3:39 pm

» E10 fuel in a 1990 VX800 - What can happen?
Bar end removal help please! Icon_minitimeby Damion Jones Tue Aug 31, 2021 3:33 pm

» Rebaffle?
Bar end removal help please! Icon_minitimeby Uneasy_Rider Sat Aug 28, 2021 3:14 pm

» Hello ... from the other side?
Bar end removal help please! Icon_minitimeby Badger Fri Aug 27, 2021 12:47 pm

» VZ800 Starter Control Relay
Bar end removal help please! Icon_minitimeby monkeyfarm Tue Aug 24, 2021 2:29 pm

» Hi newbie introduction.
Bar end removal help please! Icon_minitimeby Badger Mon Aug 16, 2021 3:10 pm

» Hello all! Bought the intruder's naked cousin, still feel like family
Bar end removal help please! Icon_minitimeby Slurpysam Sat Aug 14, 2021 9:37 am

Log in
Username:
Password:
Log in automatically: 
:: I forgot my password