Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.
Suzuki 800 Intruder Club & Forum
Welcome to suzuki800 Intruder forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, VZ800, VS800, C50, M50, Intruder / Boulevard / Marauder.

You will need to register before all the area's become visible, before doing so please enter & read the first thread in the Introductory area

It will only take a minute to register & it would be great to have you on board
This is a free to access and use site.
Suzuki 800 Intruder Club & Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Suzuki 800 Intruder Club & Forum

A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder
 
HomeRegisterLog in

 

 Programmable Gear Readout

Go down 
AuthorMessage
RetiredNotDead
Prospect




Programmable Gear Readout Empty
PostSubject: Programmable Gear Readout   Programmable Gear Readout Icon_minitimeThu May 27, 2021 10:19 pm

Has anyone had experience with an installed Dakota Digital PGR-1000 Series Programmable Gear Readout? It mounts to the handle bar and reads out 1st through 5th gear after going through the setup process. Anyway, I've had mine on the bike since around 2010, and am now seeing error messages pop up after several attempts to reset and go through setup. It works initially, but after a few miles, the blinking error messages start. Just wondering if anyone else has one of these, and whether you've had any problems after some years. It's been so long, I need to take the seat off and chase down wiring for ignition wire, neutral switch wire, speed sensor wire, and lastly, how I have this attached to the negative side of the ignition coil. I'll start from the coil first since I'm thinking that's the highest source of heat that may have the wire now exposed and perhaps shorting out somewhere. Bike is an 2006 Suzi Boulevard C50. Thanks, and stay safe, all.
-Bob
St. Johns, Michigan
Back to top Go down
 
Programmable Gear Readout
Back to top 
Page 1 of 1
 Similar topics
-
» Top Gear USA next week, one of our wagons represented?
» Transmission & gear-case fill, drain and oil
» 4WD Recovery gear what do you use?
» stuck in high gear.
» Kayaking gear for sale

Permissions in this forum:You cannot reply to topics in this forum
Suzuki 800 Intruder Club & Forum :: The Garage :: General Electrical Modifications, Help & Information.-
Jump to:  
Slide Show
A random selection of suzuki800.com member bikes.
Latest topics
» Greetings
Programmable Gear Readout Icon_minitimeby Badger Fri Jan 21, 2022 10:09 am

» low power in electrics. - Causes?
Programmable Gear Readout Icon_minitimeby Damion Jones Thu Jan 20, 2022 9:46 pm

» Hi Gals & Guys from Pete
Programmable Gear Readout Icon_minitimeby Badger Fri Jan 14, 2022 7:20 pm

» New indicators
Programmable Gear Readout Icon_minitimeby Paulw66 Sun Jan 09, 2022 8:29 pm

» VS1400 rear end on a VS750
Programmable Gear Readout Icon_minitimeby Lukaszmlynaczyk Sun Jan 09, 2022 10:02 am

» Lock the steering - VZ800
Programmable Gear Readout Icon_minitimeby ssalvado Fri Jan 07, 2022 6:42 pm

» Bike not starting
Programmable Gear Readout Icon_minitimeby compromarly@gmail.com Fri Jan 07, 2022 12:26 pm

» Filling in baffle holes
Programmable Gear Readout Icon_minitimeby Uneasy_Rider Thu Jan 06, 2022 12:52 am

» Has anyone installed a rear swingarm, from suzuki vs 1400 to vs 800?
Programmable Gear Readout Icon_minitimeby Jek Tue Jan 04, 2022 6:13 pm

» Hello from belarus
Programmable Gear Readout Icon_minitimeby Jek Tue Jan 04, 2022 2:44 pm

» Hello from NC USA
Programmable Gear Readout Icon_minitimeby pasleyspabulum Fri Dec 31, 2021 5:37 pm

» VX reg/rec location
Programmable Gear Readout Icon_minitimeby Damion Jones Wed Dec 29, 2021 8:16 pm

» Rebaffle?
Programmable Gear Readout Icon_minitimeby pasleyspabulum Mon Dec 27, 2021 12:35 pm

» Lambda sensors - HELP!
Programmable Gear Readout Icon_minitimeby Badger Mon Dec 20, 2021 7:38 pm

» Vz800 head port and polishing
Programmable Gear Readout Icon_minitimeby Dfreel43 Sat Dec 18, 2021 6:08 pm

» Another newbie from Somerset
Programmable Gear Readout Icon_minitimeby John4393 Fri Dec 17, 2021 10:20 pm

» ORIGINAL INTRUDER OWNER'S T-SHIRTS FOR ONLY $18.00 NOW!
Programmable Gear Readout Icon_minitimeby katsd Thu Dec 16, 2021 2:23 pm

» Bike Lifts
Programmable Gear Readout Icon_minitimeby Dermagraphic Wed Dec 15, 2021 12:45 pm

» Hello from Plymouth
Programmable Gear Readout Icon_minitimeby jessausten Mon Dec 13, 2021 1:33 pm

» New Member - VX800 owner from Miami
Programmable Gear Readout Icon_minitimeby Maroon VX800 Sun Dec 12, 2021 8:19 pm

Log in
Username:
Password:
Log in automatically: 
:: I forgot my password